ChrisNik,
Inc. | 800-262-4992 | sales@chrisnik.com
PIPE-MIC II
Measure pipe inverts and sizes fast, easy & accurate.
Made in the USA
Made in the USA
* Measurements are more accurate because you are measuring with a
vertical plumb rod.
* Made for Crain 25' SVR, USL rods and our new double sided PIPE-MIC II
rod.
* Made of lightweight (two pounds) non rusting aircraft aluminum.
* No tools needed to attach to rod.
* Slides on and off in seconds.
* Round foot design slices through material at bottom of pipe and
insures accurate invert and pipe diameter measurement.
vertical plumb rod.
* Made for Crain 25' SVR, USL rods and our new double sided PIPE-MIC II
rod.
* Made of lightweight (two pounds) non rusting aircraft aluminum.
* No tools needed to attach to rod.
* Slides on and off in seconds.
* Round foot design slices through material at bottom of pipe and
insures accurate invert and pipe diameter measurement.
By pulling a pin in just seconds you can go from zero to 1 ft. vertical offset for clearance under rod.
NEW PIPE-MIC II 3' Arm
Testimonial
on the PIPE-MIC II -
"We have been using the PIPE-MIC II for over 4 years and have found it to be an invaluable tool. We initially purchased it for a contract with a local sanitation district. Accurate invert elevations and pipe sizes were needed for sewer force mains, trunk lines, secondary lines as well as storm drain lines, catch basins and other structures. All of these measurements were obtained using the PIPE-MIC II, including manhole invert elevations that exceeded 25 feet; it would have been impossible to get accurate pipe sizes and inverts at the depth using the "old method". The PIPE-MIC II has not only increased the accuracy of our reading buy allowed us to obtain those readings more quickly and safely. Thank you for such a wonderful product." Jason Moore- Proactive Engineering Consultants, Inc.
"We have been using the PIPE-MIC II for over 4 years and have found it to be an invaluable tool. We initially purchased it for a contract with a local sanitation district. Accurate invert elevations and pipe sizes were needed for sewer force mains, trunk lines, secondary lines as well as storm drain lines, catch basins and other structures. All of these measurements were obtained using the PIPE-MIC II, including manhole invert elevations that exceeded 25 feet; it would have been impossible to get accurate pipe sizes and inverts at the depth using the "old method". The PIPE-MIC II has not only increased the accuracy of our reading buy allowed us to obtain those readings more quickly and safely. Thank you for such a wonderful product." Jason Moore- Proactive Engineering Consultants, Inc.
To use:
* You can direct read the depth of the invert when the pin is set at "zero offset" on the PIPE-MIC II .
* If you need clearance under rod to measure an invert move the pin to "1' vertical offset hole"
* If you need clearance under rod and a pipe that is hard to reach you can add a 1 ft. extension.
(1 ft. extension sold separately) Move pin to " 1 ' vertical offset w/ 1' extension" hole.
To size a pipe:
The foot is 0.33 or 4". Take the reading from the rim, pull up and take reading plus 0.33 and that is your pipe size.
* You can direct read the depth of the invert when the pin is set at "zero offset" on the PIPE-MIC II .
* If you need clearance under rod to measure an invert move the pin to "1' vertical offset hole"
* If you need clearance under rod and a pipe that is hard to reach you can add a 1 ft. extension.
(1 ft. extension sold separately) Move pin to " 1 ' vertical offset w/ 1' extension" hole.
To size a pipe:
The foot is 0.33 or 4". Take the reading from the rim, pull up and take reading plus 0.33 and that is your pipe size.
New Double Sided PIPE-MIC II Rod
* Made exclusively for the PIPE-MIC II
* Reduces multiple setups when using a
Total Station or Auto level.
* Printed in tenths on front & back of rod.
Part # 172510
PIPE-MIC II Double Sided Rod 25' 10th
* Made exclusively for the PIPE-MIC II
* Reduces multiple setups when using a
Total Station or Auto level.
* Printed in tenths on front & back of rod.
Part # 172510
PIPE-MIC II Double Sided Rod 25' 10th
Example:
4" Pipe - 0.00 movement
6" Pipe - 0.17
8" Pipe - 0.33
10" Pipe - 0.50
12" Pipe - 0.67
4" Pipe - 0.00 movement
6" Pipe - 0.17
8" Pipe - 0.33
10" Pipe - 0.50
12" Pipe - 0.67
®
®
®
®
®
®
®
®
Part # 1736ARM
Part # Description
1702PM2 PIPE MIC II
1736ARM 3' Arm
172510 Double sided 25'
Rod in 10th
1702PM2 PIPE MIC II
1736ARM 3' Arm
172510 Double sided 25'
Rod in 10th
®
®
®
®
®
Part # 1702PM2